General International 50-755 M1 Manuel d'utilisation et d'entretien

SPECIFICATIONSBLADE DIAMETER 12” (305 mm) ARBOR DIAMETER 5⁄8” (with 1” spacer bushing included) MAX. DEPTH OF CUT AT 90° 3” (76 mm) w/12” blade, 2”

BLADE GUARD AND ANTIKICKBACK DEVICE 1. Remove the outer blade guard.2. Remove arbor nut and outer blade flange .3. Install blade on the saw arbor with

A B CUTTERHEAD RETURN SPRING 1. Return the cutterhead assembly to rear of track arm. 2. Attach eyelet (H) of cable assembly (C) to cutterhead scr

ACCIDENTAL STARTUP CAN CAUSE INJURY. LOCKING SWITCH IN “OFF” POSITION IMPORTANT: When the machine is not in use, the switch should be locked in the “O

4. Securely lock hex nuts (A) while holding screws (B). ADJUSTING BALL BEARINGS AGAINST TRACK RAILS. WARNING DISCONNECT MACHINE FROM POWER SOURCE. A

5. Loosen cutting-head clamp knob (B), and slide cutterhead the entire length of track arm as shown to determine if blade (C) travels parallel to the

5. Place a square (C) on the table and against the saw blade, as shown, and check to see if the blade is square with the table. NOTE: The square sho

B C A D E G H K saw blade is flush against fence (D). 6. Tighten cutting-head clamp knob (G) and adjust pointer (H), if necessary, to “zero” mark on

L 6.same procedure of 45 ﾟ right and left cut. IMPORTANT: THE TRACK ARM (E), MUST BE RAISED BEFORE ATTEMPTING TO ROTATE IT. ALSO, THE PROCEDURE

A C B POSITIVE STOP BEVEL INDEX Bevel index knob (A) , provides a positive stop when positioning the saw blade at zero, 45°, and 90° left, on the

A B C ANTI-KICKBACK FINGERS During ripping operations, the splitter (A) , must ride in the saw kerf and the anti-kickback fingers (B) should be to

THANK YOU for choosing this General® International radial Saw. Thissaw has been carefully tested and inspected before shipment and if properly used an

blade through the work, just far enough to cut it off, and return the saw blade to its starting position. Turn tool off. and wait for the blade to sto

A without having to stretch or reach near the blade. Ripping involves making a lengthwise cut through a board along the grain. When ripping, the t

50-755 - TABLE AND STAND (DIAGRAM A)1

PARTS LIST 50-755 - TABLE AND STAND (DIAGRAM A)2# PART NO. REF. NO. DESCRIPTION SPECIFICATIONS QTY1 50755-A01 71011009 WOOD STRIP 23 50

50-755 - COLUMN (DIAGRAM B)3

PARTS LIST 50-755 - COLUMN (DIAGRAM B)4# PART NO. REF. NO. DESCRIPTION SPECIFICATIONS QTY1 50755-B01 50102010 CAP SCREW M8 X 1.25P X 16L

50-755 - RADIAL ARM (DIAGRAM C)521135681179101416542122172418231722212019252627161212201517281213301123129323333

PARTS LIST 50-755 - RADIAL ARM (DIAGRAM C)6IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and

50-755 - MOTOR BRACKET (DIAGRAM D)7

PARTS LIST 50-755 - MOTOR BRACKET (DIAGRAM D)8# PART NO. REF. NO. DESCRIPTION SPECIFICATIONS QTY1 50755-D01 50101066 HEX BOLT M12 X 1.75P X

RULES FOR SAFE OPERATION1. Do not operate the saw when tired, distracted, or under the effects of drugs, alcohol or anymedication that impairs reflexe

PARTS LIST 50-755 - MOTOR BRACKET (DIAGRAM D) - CONTINUED9# PART NO. REF. NO. DESCRIPTION SPECIFICATIONS QTY51 50755-D51 71014003 FRONT CENTR

PARTS LIST 50-755 - MOTOR AND BLADE (DIAGRAM E)1011223454678910111213141617182425221262728.1322111523113202120131920292030312828.228.3

PARTS LIST 50-755 - MOTOR AND BLADE (DIAGRAM E)11IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machi

20. Use of parts and accessories NOT recommended by GENERAL INTERNATIONAL may result inequipment malfunction or risk of injury. 21. Never stand on mac

UNPACKING AND CLEANINGCarefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainte

HARDWARE BAG 1. SCREW DRIVER 1 PCS 2. WRENCH 11/13,12/14,21/23 3PCS 3. ALLEN KEY 2PCS 4. KEY FOR SWITCH 1PCS 5. FOOT PAD WASHERS AND SCREWS 4PCS 6. K

ATTACHING STAND TO THE MACHINE 1. Assemble the stand first. with 16 shoulder bolts, washers and hex nuts, begin assembling oneend of stand by attachin

ATTACHING THE OVERARM ELEVATING HAND WHEEL 1. Fasten the elevating handle wheel knob to the elevating wheel(A).2. Adjust cable hanger to “B” position.

ADJUSTING TABLE TOP PARALLEL TO TRACK-ARM For accurate work the track-arm must be parallel to the table top at all points. To check and adjust: 1. Mov