General International 30-005HC M1 Manuel d'utilisation et d'entretien

SPECIFICATIONSTABLE AREA WITH EXTENSIONS (L X W)28 3⁄8” X 13” (720 X 330 MM)MAXIMUM PLANING WIDTH13” (330 MM)MAXIMUM THICKNESS OF STOCK6” (152 mm)MINI

This planer is equipped with a rocker style ON/OFF switch located on the front left hand side of the cutter head. Tostart the planer, insert the lock-

DEPTH OF CUT INDICATORThe depth of cut indicator, A, will indicate how muchmaterial the cutterhead is set to remove from the work-piece for a given pa

THE MAXIMUM PLANING WIDTH OF THIS UNIT IS 13”. THE MAXIMUM WORKPIECE THICKNESS OF THIS UNIT IS 6” THE MINIMUM THICKNESS TO WHICH A WORKPIECECAN BE SAF

1. With the planer turned off, position the workpiece on the infeed table with the flat face down and the face to be planed facing up.PLANING STEP-BY-

1410. The return rollers on the top of the planer can be used to pass the workpiece back to the front of the machine for repeat passes.11. Repeat thes

15MAKE SURE THE PLANER HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMINGANY MAINTENANCE.INSPECTING/REPLACING CUTTERHEAD KNIVES

4. Using the supplied allen key, loosen and remove the 2 button head screw B, then remove the chip deflector.5. Insert the supplied allen key into the

REPLACING THE V-BELTThe cutter head is driven by a flat ribbed belt that is located on the right-hand side of the planer facing the infeedside.17DRIVE

RECOMMENDED OPTIONAL ACCESSORIESWe offer a large variety of products for increased convenience, productivity, accuracy and safety when usingyour plane

6543210151413121110987654321027(3)44(2)43(2)5236(10)40(4)2032(4)31(4)48(4)35(4)39(4)50(4)49(4)47(4)46(12)302928(4)2621194534(5)33(4)218(15)910(3)14(2)

THANK YOUfor choosing this General®International model 30-005HC M113” Planer with Helical Cutter Head. This planer has been carefully tested and inspe

78(8)174(2)171170(2)172(2)173(2)1835756167168(2)61585960(11)6364(2)66164163(2)1621591618180(6)8283(2)85(2)84(2)176175178177(4)158151152153156155123(4)

21PARTS LIST30-005HC M1PART N0. REF. N0. DESCRIPTION SPECIFICATION QTY1 30005-01 HANDLE ASSEMBLY 12 30005-02 CAP SCREW M5xP0.8x20L 18 30005-08 BUTTON

22PARTS LIST30-005HC M1PART N0.REF. N0. DESCRIPTION SPECIFICATION QTY61 30005-61 CUTTER HEAD BEARING SEAT 162 30005-62 CUTTER HEAD BEARING 6203ZZ 263

PARTS LIST30-005HC M1PART N0. REF. N0. DESCRIPTION SPECIFICATION QTY161 30005-161 MOTOR FAN COVER 1162 30005-162 WAVE WASHER 1163 30005-163 BEARING 62

IMPORTANTWhen ordering replacement parts, always give the model number, serial number of the machine andpart number. Also a brief description of each

GENERAL®& GENERAL®INTERNATIONAL WARRANTYAll component parts of General®, General® International and Excalibur by GeneralInternational ® products a

TABLE OF CONTENTSRules for safe operation . . . . . . . . . . . . . . . . . .5Electrical requirements . . . . . . . . . . . . . . .6Grounding instru

1. Do not operate this planer when tired, distracted, or under the effects of drugs, alcohol or any medication that impairs reflexes or alertness.2. T

6ELECTRICAL REQUIREMENTS GROUNDING INSTRUCTIONSIn the event of an electrical malfunction or short circuit,grounding reduces the risk of electric sho

IDENTIFICATION OF MAIN PARTS AND COMPONENTSIN-FEED TABLESTOCK THICKNESS SCALEHEIGHT ADJUSTMENT HANDLERETURN ROLLERSCIRCUIT BREAKERON/OFF SWITCH W/SAFE

Carefully unpack and remove the planer and its compo-nents from the box and check for damaged or missingitems as per the list of contents below.NOTE:

ATTACH THE DEPTH OF CUT ADJUSTMENT HANDLEATTACH THE DUST CHUTEAttach the adjustment handle on top of the machineas shown, using the supplied allen key